UDSflow

Please feel free to post reviews of new barbecues, gadgets and of course food. The opinions within the forum are not necessarily that of the web site owner!

UDSflow

Postby aris » 31 Aug 2012, 19:43

Image

This is the arduino based airflow controller so far.

So I have an Arduino Nano on a mini-breadboard, controlling an external temperature/humidity sensor, a relay (to switch the fan on), an IR proximity sensor (to detect when the UDS lid comes off), the Maveric ET-73 pit probe, and a bluetooth transmitter/receiver which is transmitting all the data to the Android tablet you see in the back. This is all being powered by two 18650 2400MaH lithium ion batteries - these are 3.7v each. I'm hoping this will last for 12-18 hours - if not i'll double up with 4 of these, or look into some power saving techniques on the arduino by putting the processor to sleep when it is not being used.

At the moment the probe is giving some odd readings - i'm guessing because it is not hot enough, it is outside its range and giving these spurious readings. If so, i'll have to take care of that in the code.
aris
Rubbed and Ready
Rubbed and Ready
 
Posts: 1426
Joined: 06 Jul 2012, 13:18
Location: UK

Re: UDSflow

Postby BBQFanatic » 31 Aug 2012, 19:58

Looks like a labour of love that!
BBQFanatic
Moderator
Moderator
 
Posts: 277
Joined: 20 Oct 2010, 13:45
Location: SW London

Re: UDSflow

Postby aris » 31 Aug 2012, 20:15

Certainly is fun.

As i'm busy seasoning my UDS - and there were some coals going, I thought i'd take it out and test it. I figured out why i was getting spurious readings from the probe. The ET-73 2.5mm jacks are a few mm longer than a regular audio jack - and the sockets I got were presumably designed for audio. Pulling the jacks out a few mm sorted the problem - saw my probe go to around 400F when inside the UDS.

Now that it is back inside, it is slowly coming down. This probe isn't exactly a Thermapen when it comes to instant readings - but that is fine for the job it is doing.

Might glue or solder a small washer to the jack so that it never goes in too far. A spurious or incorrect reading would be disastrous!
aris
Rubbed and Ready
Rubbed and Ready
 
Posts: 1426
Joined: 06 Jul 2012, 13:18
Location: UK

Re: UDSflow

Postby aris » 05 Sep 2012, 14:51

Did a test (indoors) and the unit ran for 30 hours on one charge. I'm using two 18650 rechargable Lithium Ion batteries in series. These batteries are 2400mAh @ 3.7v - so a total of 7.4v @ 4800mAh. 30 hours should be adequate for a good smoke. This included bluetooth transmission to an android tablet, and switching the relay on and off. The fan has its own power supply - 4 AA batteries. The relay just switches this fan on and off.

After looking at the PID code, I decided against it. I may add it in later, but for now it just looked too complicated and there were just too many input variables affect it. I'm going for a pure thermostat model. If it is below a certain temperature, blow, if not, don't.

In theory I could add 5 food temperature sensors to this unit plus another for the pit itself - making 6 in total. At the moment i'm working with one for the pit and one for the food.
aris
Rubbed and Ready
Rubbed and Ready
 
Posts: 1426
Joined: 06 Jul 2012, 13:18
Location: UK

Re: UDSflow

Postby derekmiller » 05 Sep 2012, 14:55

Hi Aris.
If they are in series then you will have 7.4v @2400mAh. The voltage will double but the current will remain the same.
derekmiller
Site Admin
Site Admin
 
Posts: 642
Joined: 02 May 2012, 12:20
Location: Cotton End, Beds

Re: UDSflow

Postby aris » 05 Sep 2012, 17:20

Quite right! I'm not an EE and was not thinking straight :-)
aris
Rubbed and Ready
Rubbed and Ready
 
Posts: 1426
Joined: 06 Jul 2012, 13:18
Location: UK

Re: UDSflow

Postby aris » 27 Sep 2012, 16:59

In case you were wondering. Progress has been slow due to other priorities - but it's in a box now.

Image

Basically an Arduino Nano, with a sensor shield to make things a bit easer while testing and plugging things in/out.

Bluetooth module

Humidity/temperature module (the blue thing on the outside)

Two sockets for a pit and food probe - with plenty of scope to add more if needed (about 6 or 7 I should imagine)

And a relay to switch a fan on/off.
aris
Rubbed and Ready
Rubbed and Ready
 
Posts: 1426
Joined: 06 Jul 2012, 13:18
Location: UK

Re: UDSflow

Postby Toby » 27 Sep 2012, 18:06

Looks Smart!
User avatar
Toby
Site Admin
Site Admin
 
Posts: 1054
Joined: 18 Jan 2012, 15:28
Location: Surrey, UK

Re: UDSflow

Postby aris » 27 Sep 2012, 18:44

Thanks - with the cover on it just looks like a box with some connections though :-)

Now onto the UDS itself - if the weather cooperates, i'll hopefully get a bunch done this weekend.
aris
Rubbed and Ready
Rubbed and Ready
 
Posts: 1426
Joined: 06 Jul 2012, 13:18
Location: UK

Re: UDSflow

Postby keith157 » 28 Sep 2012, 05:29

You could always go the McClaren route and make a new top of clear acrylic to show off the innards. Great work
User avatar
keith157
Moderator
Moderator
 
Posts: 3816
Joined: 05 Aug 2011, 13:35
Location: Stevenage, Herts


Return to Barbecue Reviews

Who is online

Users browsing this forum: No registered users and 14 guests